Mike_da_Spike

Can you post your latest pinballx.ini and a log file from the capturing ? Has the files created in the table video folders the same date/time stamp as in the backglass videos?

Graag gedaan ! How is your issue with the avangers.directb2s file?

Just download ffmpeg and put the file into the pinballx directory. Not sure if it is allowed to put the file in the post

I had the same in the past. Not sure how I fixed, but I thought it has to do with the b2sTablesettings.xml Open it with notepad, find the section for avengers. Check if it is different than the other tables (like use exe) You can also delete the section and launch the table again. Hope this helps

I had the same with my Samsung Tv when starting the cab. Removing the Hdmi and put back was a workaround During powering on of the cabinet, the pc started on a 4k 60hz resolution mode, but the TV was starting in 4k 30p. This gave me the same behaviour. First as workaround I set the resolution to 4k 30hz when shutting down the pc and at startup of pbx I moved it to 4k 60hz again. Finally I changed a setting in the Tv. Set it to pc mode (but that causes some lag) and another setting (that prevents the lag), but not sure what the setting was) That fixed iyt for me And use HDMI1 port !!

Not sure if it is the best approach, but you can detach the harddrive from the system and add it to another system. Copy over all relevant data from the harddrive. Reinstall operating system and start all from scratch. Thats what I should do, but no guarantee from my side

How did you setup the tables in gamemanager ? Did you put the correct tables to the correct vp version? Best is to create sub dirs and put the correct table files in there

Yup. Have that too

I have created real dmd videos with a resolution of 128x32 as mp4 file. Cost me a lot of time to figure out what the best codecs where, but finaly made them work.

If I have some time tomorrow I will try your xml files and your pinballx.ini file on my cabinet

I think you better check the eventlog of you computer what is causing this. Maybe a corrupted piece of .net

@mkend5 whats the latest status now ?

Well. Thats the issue. If I want to launch it, it says about a new version and wont launch at all. But as Draco said, why you just update the TPA version and uses the latest FCM ? Mine is always updating automaticly trough steam to the latest version (and to be honnest, I like the vpx table better than the TPA tables)

Maybe stupid question, but how can I see on the exe file which version it is ? I got a couple of back ups from the last couple of months, but checking the details it shows me 1.3.3.7. Launching the exe result that it want to update and not launching at all Please let me know, maybe I have a copy for you

Per table/rom you can also change the volume of the roms sounds/music. Most of my roms where set with low volume. Changing that when game was running sounds nice.

I think pinballx freezes on your initialization of your DMD. Can you try to set AutoPositionPinmane to false ? If that doesn't work, try to disable the Dmd itself to check if pinballx is not freezing

So, if it is showing another popup, it looks like it is not freezing. According to your ini file you only have fx3 enabled and shows the last table it showed was worlwar hulkmarvel. Did you setup all good within gamemanager ? If you launch settings and got to the end, there is a validate button. Is that showing all correct ? If you have the error, are you able to close pinballx and post the log.txt again ?

Not sure if this causes issues, but under your [pinballarcade] section in the ini file I don't see an entry enabled=true/false

3. "I normally shut down with power switch and have no problem when booting up again? " Do you mean that you don't give a graceful shutdown, but just power off your machine? What settings do you loose in the ini file? Did you check timestamp after rebooting, to see when the file was changed ? If you configure DOF correctly. It will not affect anything (I guess you refer to the lag of your flippers) Logfile and settings file will be a 'nice to have' to troubleshoot (simulate your issue before posting logfile)

Using Geforce Experience driver to capture video's within PBX : Open your Geforce experience Press Alt+Z to bring up the Share overlay and go to Settings : NOTE: If the Share overlay does not appear it may be turned off. You can turn it on inside GeForce Experience by going to Settings > GENERAL > SHARE and toggling the switch. It will light up green indicating the Share overlay has been turned on. In Settings, click on Recordings: Set the path where the video’s will be recorded. For example c:\pinball\pinballx\GeforceCapture Hit the Back button and hit Done Check under Records what the key is to start a record. By default it is Alt+F9 Close the Share Overlay Open PinballX Setup Wizard and select Video recording in the left pane Select Use GPU driver capture to Yes Make Sure that the Driver record start/stop key are the same as the hotkey that is defined in the Geforce Experience Share overlay screen Set the Driver save path to the same directory as the Recording path in the Geforce Experience Share overlay screen Save your settings ! (sorry for the Dutch Screenshots, but could not set it to English)

Awesome Tom ! I made a mistake. If I select in Geforce experince a folder, I normally dubbelclick that foler. but than it uses a subfolder. Just browsinf (for me) to c:\pinball and select pinballx did the trick ! Now it is capturing correctly. I will write down a little manual, so that others can use this too. (maybe it's already there, but could not find it) Thakns Tom for helping me out on this ! I really appriciate all your work you put into this nice front end tool and helpgin people on this forum !

This is function is added too gamemanager in pbx. And yes you can capture the TPA tables too.

Odd issue @joyrider3774. I suspect teamviewer for some reason. Hope you find the solution soon

Didn't see this issue at all on my cabinet. Do you have installed teamviewer on your pc too ? I just use rdp to get into my cab. Also support multimonitor Maybe try full post it on the Zen studio forum ?

I have indeed pbx32 bit running on my windowd 10 64 bit